tag:blogger.com,1999:blog-5721739675993007342.post1174486627474929221..comments2023-10-18T12:46:39.694+03:00Comments on Mini Sumo Robot "Destroyer 3000": Start Module Implement YourselfAnonymoushttp://www.blogger.com/profile/07950520177154940670noreply@blogger.comBlogger6125tag:blogger.com,1999:blog-5721739675993007342.post-43923798452866942522019-01-07T21:01:01.225+02:002019-01-07T21:01:01.225+02:00Is it reference / interface / include operator, I ...Is it reference / interface / include operator, I am not best at c programming.Anonymoushttps://www.blogger.com/profile/07950520177154940670noreply@blogger.comtag:blogger.com,1999:blog-5721739675993007342.post-27632984283126105462017-12-11T19:52:54.515+02:002017-12-11T19:52:54.515+02:00Hi,
The last time i used this instructions:
=====...Hi,<br />The last time i used this instructions:<br /><br />====================== Programming the device<br /><br />For those who want to build their own modules based on this code and microcontroller, it is important that the fuse are correct when uploading the hex-file. Incorrect settings may brick your chip.<br /><br />Using the following avrdude command is used when programming the prebuilt modules. It utilizes the AvrISP MKII programmer, so if you use any other programmer, change the programming command accordingly. Make sure to be in the correct folder, or replace "StartModule.hex" to the correct path to your hex-file.<br /><br />avrdude -pt13 -cavrispmkII -Pusb -u -Uflash:w:StartModule.hex:a -Ulfuse:w:0x79:m-Uhfuse:w:0xef:m<br /><br />These fuse bits sets the following. The ones marked (important) have the potential to brick your system if set incorrectly. Set them as below and you should be fine:<br /><br />No brownout detection<br />No clock division by 8<br />No Debug wire<br />No Eeprom preserve through programming<br />No reset disable (important)<br />Self Programming enabled (important)<br />SPI programming enabled (important)<br />Clock source as 4.8MHz, 14CK 64ms startup time (important)<br />No watchdog<br />You can check http://www.engbedded.com/fusecalc for further information about fusebtis.<br /><br />When the flash has been written, the module will go into "Stopped" state, which means it will blink slowly. Cycle the power and it should be ready to use.Valterhttps://www.blogger.com/profile/07969320144552118722noreply@blogger.comtag:blogger.com,1999:blog-5721739675993007342.post-15971504799751168352017-12-11T02:18:46.836+02:002017-12-11T02:18:46.836+02:00hello I have problems to record the hex to the con...hello I have problems to record the hex to the control you can help me to record itkamtronichttps://www.blogger.com/profile/01937406810942487466noreply@blogger.comtag:blogger.com,1999:blog-5721739675993007342.post-81566388978638217472017-05-03T17:53:32.729+03:002017-05-03T17:53:32.729+03:00Hi,
Yesterday I tested your program with "Ard...Hi,<br />Yesterday I tested your program with "Arduino Uno"<br />All works !!!!<br />But it's necessary change the original code:<br />State powerOnState = State(powerOnEnter, powerOnUpdate, powerOnExit);<br />State idleRunState = State(idleRunUpdate);<br />State stoppedState = State(stoppedSafe,stoppedUpdate, NULL);<br /><br />with correct code (including &):<br />State powerOnState= State(&powerOnEnter, &powerOnUpdate, &powerOnExit);<br />State idleRunState= State(&idleRunUpdate);<br />State stoppedState= State(&stoppedSafe,&stoppedUpdate, NULL);<br /><br />After programming led flashing 3 time !!<br /><br />Good Job<br />Thanks<br />Valterhttps://www.blogger.com/profile/07969320144552118722noreply@blogger.comtag:blogger.com,1999:blog-5721739675993007342.post-66179678305381418632016-10-20T10:20:56.622+03:002016-10-20T10:20:56.622+03:00How am I supposed to help you?How am I supposed to help you?Anonymoushttps://www.blogger.com/profile/07950520177154940670noreply@blogger.comtag:blogger.com,1999:blog-5721739675993007342.post-63671048900956614042016-10-20T00:58:29.336+03:002016-10-20T00:58:29.336+03:00hola me puedes ayudar en que parte del codigo colo...hola me puedes ayudar en que parte del codigo coloco mi progrmacion y cambio el numero de dato que envioAnonymoushttps://www.blogger.com/profile/04399327448260239432noreply@blogger.com